Data Centre Water Tank RFQ: What To Put In The Enquiry

10_1.jpg

Data Centre Water Tank RFQ: What To Put In The Enquiry

A data centre water tank RFQ must state the duty and volume basis, reference the governing code and construction standard by name and edition, define the material, coating and construction, request the documentation package, and give site and logistics data. Quotations are only comparable when they answer the same RFQ against the same volume basis and scope.

Introduction

An enquiry for a data centre water tank is a document before it is a purchase. The quality of the quotations you receive is set almost entirely by what you put in the request, because suppliers quote the enquiry they are given, and an enquiry that leaves the duty, the code or the coating open will return prices that look comparable on the page and are not comparable in the tank. The work of buying the tank is mostly the work of writing the request.

 

This guide treats the RFQ as a document with a job to do: give the supplier enough to quote without a clarification round, define the terms that keep quotations on the same basis, and build the evaluation matrix that follows. The topics are the duty and volume basis, the codes and standards to reference, the materials, coating and construction to define, the deliverables and documentation to request, the site and logistics information, and the issuing and evaluating discipline that closes the loop.

 

Two conventions apply. A standard is not a certification, so reference the construction standard and the fire-protection standard by name and edition, and let the supplier demonstrate compliance through documents rather than a mark. And the volume you state should be the usable or effective volume the system draws from, never only a nominal figure, because that single definition decides whether two quotations are even about the same tank.

Why enquiries come back incomparable

Enquiries come back incomparable for a small set of repeated reasons, and every one of them is a missing definition in the request. The volume is stated as a single nominal figure while suppliers assume different unusable volumes, so the usable capacity behind each price differs. The code is named without an edition, or the construction standard is omitted, so each supplier designs to a different basis.

The coating is described by performance rather than by a named system, the scope split between tank, foundation and installation is left to the supplier, and the documentation package is not requested at all, so the lower price simply omits it. The fix is not a longer form; it is a request that defines each of these items explicitly, so every quotation is an answer to the same question rather than to eight different ones.

The duty and volume basis to state

State the duty first: what the tank serves, the fluid, the temperature range, and whether it is fire protection, cooling make-up or process water. Then state the volume basis in the words the design uses - the fire flow and duration, or the make-up demand and reserve - and give the nominal, usable and effective volumes separately, defining the unusable volume from draw-off level, heel and any dead pocket.

The point of separating the volumes is that the pump draws the usable volume, and a quotation priced on nominal volume can look cheaper while delivering less of the capacity the system needs. State also the operating level range, the fill source and rate, the draw rate, and any redundancy or duty-standby arrangement, because these set the nozzle and appurtenance scope the supplier must price.

Code and standards to reference

Reference the codes by name and edition so the design basis is fixed. For fire protection, NFPA 22 is the design standard and it points to the construction chapter that matches the tank: Chapter 6 for factory-coated bolted carbon steel tanks, Chapter 5 for welded steel gravity tanks, with the cross-cutting chapters - foundation, pipe connections, appurtenances, heating, acceptance and inspection - applied on top.

Name the construction standard too: AWWA D103 for bolted tanks, AWWA D100 for welded tanks, and ASME BPVC Section VIII where the tank operates under pressure. Citing the edition of each standard removes the ambiguity that lets two suppliers design to different rules, and it gives the authority a fixed set of requirements to review against, which shortens the approval path as much as the quotation path.

Materials, coating and construction to define

Define the material, coating and construction so the quotation prices a real tank. State the tank type and the construction standard together, the shell and roof material and grade, and for a bolted tank the coating system from the four AWWA D103 options - galvanized, glass fused to steel, thermoset liquid suspension or thermoset powder - with the surface preparation, the dry-film thickness and the holiday-test requirement.

For a welded tank, reference the AWWA D102 coating with the same level of detail. Define the roof type, the access and platform requirements, the nozzle schedule and the appurtenances the chapters require, and where the stored water must stay above freezing, the heating of NFPA 22 Chapter 16. A quotation that meets a named system is checkable; one that meets a performance promise is not, and the RFQ is where that distinction is set.

Deliverables and documentation to request

Request the documentation package as a priced deliverable, not as an afterthought. The set should cover the approved drawings and calculation basis, the material certifications with traceability, the welding procedure and qualification records where welding applies, the coating specification with preparation, thickness and test results, and the inspection and test plan with named hold points.

Also request the acceptance test records and the inspection, testing and maintenance programme the tank inherits at handover, because these are the documents the owner uses for the life of the asset. By requesting them with the quotation, you force each supplier to price the same evidence set, and you remove the typical gap where the lower price quietly drops the records the authority will later demand.

Site and logistics information

Give the site and logistics information so the quotation prices the real delivery, not an ideal one. Provide the location and access route, the ground conditions or the geotechnical status, the seismic and wind parameters under the adopted building code, the available crane and laydown space, and any limits on transport width, weight or height to the site.

State also who designs the foundation - usually the engineer of record for the site - and what loading schedule the tank supplier must furnish for it. A remote or constrained site changes freight, crane and erection cost by more than the tank-type choice for some projects, and an RFQ that omits access data simply shifts that cost into a variation after award, where it is no longer comparable between bidders.

The comparison matrix

Build the comparison matrix as part of issuing the RFQ, so you evaluate what you defined rather than what was easy to read. The matrix lists, for each quotation, the tank type and standard, the capacity basis, the named coating system, the documentation package, the freight and installation scope, and the exclusions, scored against the same weights you set from the duty risk.

· Volume basis: nominal, usable and effective stated and matched across bidders.

· Code and edition: NFPA 22 plus the construction standard, both named.

· Coating: system named, with preparation, thickness and test method.

· Documentation: design, coating, ITP and acceptance records all present.

· Scope split: tank, foundation and installation defined and consistent.

· Exclusions: listed explicitly so gaps are visible, not hidden.

Issuing and evaluating

Issue the RFQ with a clear question format - a table the supplier fills - and a stated deadline and a single technical contact, so clarifications come to one place and the basis stays controlled. Allow a short clarification window, but require that any deviation from the stated basis be flagged in a defined exceptions section, so a non-compliant quotation is visible at opening rather than discovered at review.

Evaluate by scoring the matrix, not by ranking the headline price. Where two quotations differ, trace the difference to the driver - a different coating, a missing document, a different volume basis - and resolve it before award. The enquiry that produced comparable quotations is the enquiry that made the comparison trivial, and the matrix is the record that keeps the decision defensible.

RFQ Information Checklist: Item, Why Needed, Where It Goes

Item

Why Needed

Where In The RFQ

Duty and fluid

Sets the tank type and the chapters that apply

Duty section, with temperature and service

Volume basis

Nominal, usable and effective differ; pump draws usable

Capacity section, all three stated

Code and edition

Fixes the design basis for every bidder

Standards section, named and editioned

Coating system

Largest variable within a route

Materials section, named with test method

Documentation set

Usually missing from the lower price

Deliverables section, as a priced item

Site and logistics

Prices real freight and erection, not ideal

Site section, with access and ground data

Quotation Comparison Matrix: Criterion, Weight Basis, What To Score

Criterion

Weight Basis (duty risk)

What To Score

Volume basis

High - sets usable capacity

Nominal, usable and effective matched across bidders

Code and edition

High - fixes design rules

NFPA 22 plus construction standard, both editioned

Coating

High for water or corrosive duty

Named system, preparation, thickness, test

Documentation

Medium-high - authority and life records

Design, coating, ITP, acceptance records present

Scope split

Medium - avoids hidden cost

Tank, foundation, installation defined and consistent

Exclusions

Medium - reveals the gaps

Listed explicitly, not left blank

Project Reference

No project reference matching this topic is on record in the verified case library, so no installation is cited here. The guidance is built on the RFQ structure and the quotation-comparison framework above - the duty and volume definitions, code references, coating and documentation scope, and the evaluation matrix - which a buyer applies to the specific project rather than to a published case.

About Center Enamel

Center Enamel (Shijiazhuang Zhengzhong Technology Co., Ltd.) designs and fabricates bolted steel storage tanks, welded steel tanks, fusion-bonded epoxy tanks, galvanized tanks, stainless steel vessels, pressure vessels, aluminum geodesic dome roofs and floating roofs. The company has more than 30 years of production experience and has supplied equipment to projects in more than 100 countries. Aluminum geodesic dome roofs are designed and fabricated to API 650 Appendix G, AWWA D108, the Aluminum Design Manual, ASCE 7 and IBC, and the company developed and exported a 72 m diameter aluminum dome roof in 2023. Engineering, fabrication, coating, quality control and site service are handled as one scope, which is why the drawings, the calculation basis and the delivered hardware can be reconciled against each other.

Frequently Asked Questions

What should a water tank RFQ contain?

A water tank RFQ should contain the duty and volume basis stated as nominal, usable and effective volume, the governing code and construction standard by name and edition, the material and named coating system, the nozzle and appurtenance scope, the documentation package requested as a deliverable, and the site and logistics data. Issued as a fill-in table with a single technical contact, it returns quotations you can compare without a clarification round.

How do I get comparable quotations from suppliers?

Get comparable quotations by defining every driver in the RFQ so each supplier answers the same question. State the volume basis identically, reference NFPA 22 and the construction standard by edition, name the coating system rather than a performance, set the scope split between tank, foundation and installation, and request the same documentation package. Score the returns on a pre-built matrix, and treat any blank line as an unpriced item.

What duty information does a supplier need to quote?

A supplier needs the duty - service, fluid, temperature range - and the volume basis in the design's own words: fire flow and duration or make-up demand and reserve, with nominal, usable and effective volumes. Also provide the operating level range, fill source and rate, draw rate, redundancy arrangement, and the nozzle and appurtenance scope, because these set the design the supplier must price and the code chapters that apply.

Which standards should the RFQ reference?

Reference NFPA 22 for fire-protection water tanks, naming the chapter that matches the construction - Chapter 6 for factory-coated bolted tanks, Chapter 5 for welded steel gravity tanks - with the cross-cutting chapters applied on top. Add the construction standard by edition: AWWA D103 for bolted tanks, AWWA D100 for welded tanks, and ASME BPVC Section VIII where the tank is pressurised. Naming the edition fixes the design basis for every bidder.

What documentation should be requested with a quotation?

Request the approved drawings and calculation basis, the material certifications with traceability, the welding procedure and qualification records where welding applies, the coating specification with preparation, thickness and holiday-test results, the inspection and test plan with named hold points, and the acceptance test records plus the inspection, testing and maintenance programme. Asking for these with the quotation forces each bidder to price the same evidence set.

How should quotations be evaluated?

Evaluate by scoring a pre-built comparison matrix weighted to the duty risk, not by ranking the headline price. Score the tank type and standard, the capacity basis, the named coating system, the documentation package, the freight and installation scope and the exclusions across bidders. Trace any price difference to its driver - coating, document or volume basis - and resolve deviations before award so the decision is defensible.

What causes a clarification round?

A clarification round is caused by an open definition in the RFQ: a nominal-only volume that suppliers interpret differently, a code named without edition, a coating promised by performance rather than named, an undefined scope split, or missing site and logistics data. Each gap forces a question back to the buyer, and the answers change the price. Closing those definitions before issue is what removes the clarification round.

Conclusion

The enquiry is the purchase. A data centre water tank RFQ that states the duty and volume basis, references NFPA 22 and the construction standard by edition, defines the material, coating and construction, requests the documentation package, and gives the site and logistics data will return quotations that are answers to the same question, which is the only kind you can compare and the only kind you can approve.

 

Build the comparison matrix as you issue the RFQ, evaluate by scoring it, and trace every price difference to its driver before award. Send us the duty, the volume basis, the governing code and the site constraints, and we will return an RFQ template and a comparison sheet you can issue, with the coating system and the documentation scope stated rather than implied.

Talk To Our Engineering Team

Send the duty, the volume basis, the governing code and the site constraints, and our engineering team will come back with a specification that a supplier can price and a reviewer can approve. We will also tell you plainly when a different tank type or a different scope is the better answer.

Sources And References

1. ASME BPVC Section VIII, Rules for Construction of Pressure Vessels

2. AWWA D103, Factory-Coated Bolted Carbon Steel Tanks for Water Storage

3. NFPA 22, Standard for Water Tanks for Private Fire Protection

Chat with us